Home / Inside the technology

Inside the technology

Every number behind every step.

The engineering, the lab tests and the manufacturing behind RobotSole footwear, as RobotSole publishes them. Open the section you need.

01Three-layer architectureRigid where it carries, soft where it lands.

The sole borrows the rigid–flexible logic of the human foot and of radial tires. Softer is not better: an overly soft material compresses flat on impact and passes the energy straight to the joints. RobotSole uses gradient stiffness instead: a hard contact layer, a soft cushion layer and a rigid base.

LayerMaterialFunction
Contact layer (outsole)~70A wear-resistant rubberFriction, wear and oil resistance, zoned anti-slip tread
Cushion layer (midsole)~40A elastic TPV, gradient foamHigh-rebound energy absorption and energy return
Base layer (support)7075 aluminum plate + large metal washerRigid support and secure fastening
02Performance vs. the industry baselineEight properties, all above the international baseline.
PropertyRobotSoleBaseline
Shock absorption≥60%≥50%
Compression set, 70 °C × 24 h≤18%≤20%
Dry friction (μ)≥0.6≥0.5
Anti-slip angle≥35°≥30°
Akron abrasion≤0.20 cm³ / 1.61 km≤0.25 cm³ / 1.61 km
Tensile strength≥15 MPa≥13 MPa
Tear strength≥40 kN/m≥35 kN/m
Hardness63–78 Shore A60–75 Shore A

RobotSole targets and measured values for the humanoid bionic shoe.

03Wear and abrasion testsAkron abrasion tester, per GB/T 1689.

Measured samples

cm³ lost per 1.61 km. Lower is better.

ZL-PAD-70A0.03
TPU sample0.05
Rubber 60#0.12
Rubber 50#0.29

Reference values, common rubbers

Typical Akron abrasion range, cm³ / 1.61 km.

Polyurethane (PU)
0.03–0.1
Nitrile rubber (NBR)
0.1–0.2
Natural rubber (NR)
0.2–0.3
Silicone (Q)
0.5–0.8

Wear life: RobotSole soles are designed for more than 8,000 hours, against 2,000–3,000 hours for mainstream rubber soles.

04Wet grip (DMA)The same method used to rate tire treads on wet roads.

Wet-slip index, tan δ at 0 °C

Higher is better.

ZL-PAD-70A0.536
TPU sample0.258
Natural rubber 700.137
Equipment
Dynamic mechanical analysis (DMA)
Frequency
10 Hz, industry standard for wet-slip (ISO 4664-2, ASTM D5992)
Mode and strain
Tensile, 0.3% strain (linear viscoelastic range)
Temperature sweep
−40 to 80 °C at 3 °C/min
05ZL-PAD compound data sheetTypical laboratory values, with the test standard for each.
PropertyZL-PAD-40AZL-PAD-70AStandard
Density1.2 ± 0.1 g/cm³1.2 ± 0.1 g/cm³GB/T 533
HardnessShore A 40 ± 5Shore A 70 ± 5GB/T 39693.4
Tensile strength8 MPa≥10 MPaGB/T 528
Elongation at break500%≥300%GB/T 528
Compression set, 70 °C × 24 h, 25%20%15%GB/T 7759
Loss factor, tan δ max1.20.72GB/T 9870.1
Recommended temperature−45 to 140 °C−45 to 140 °C—

Test sheets vulcanized at 170 °C × 20 min, 10 MPa.

06Design detailsSmall engineering choices with a measurable effect.
Toe and heel spring
10–15° approach and 8–12° departure angles for slopes, stairs and ditches, without changing contact area or control data.
Zoned tread
Transverse grip grooves at the forefoot, a cushioning pattern at the heel and reinforcing ribs at the arch.
Large built-in metal washer
The lock nut clamps on metal, not soft rubber, for higher pull-out strength.
Bumper rubber
Toe, heel and side bumpers absorb collisions and protect the robot.
Standard interface
Unified hole positions, locating dimensions and interface specs across models and generations.
Ready for sensors
Reserved slots and hidden wiring for force and multi-modal sensing.
07Manufacturing and quality controlFive phases, from 3D data to final inspection.
  1. Design and developmentJoint work on your 3D data, structure and materials, with a three-party sample sign-off.
  2. Molds and trial moldingSteel molds for the dual-density outsole and the PU upper, with a Teflon-coated surface for a cleaner finish.
  3. Outsole production and lab testingDual-density vulcanization, then material, slip-friction and abrasion tests, with an official factory lab report.
  4. Integrated injection moldingThe outsole and aluminum plate are loaded into the mold and the PU upper is injected around them: no adhesive.
  5. Finishing and final inspectionLogo printing, then a full check of appearance, dimensions and adhesion before packing.
08Industrial backingThe production base behind every pair.
Partner production bases
Over 70,000 m² in northern China and Guangdong, with PU, TPR, rubber, TPV and carbon fiber capability.
Sole factory
Around 12 million pairs a year, certified ISO 9001, ISO 14001 and ISO 45001.
Materials partner
Strategic partnership with Dawn Polymer (002838.SZ), a listed company, sharing a new-materials lab for robot-sole TPV.
Aluminum plates
CNC-machined and anodized in an ISO 9001 precision hardware plant.
Patents
30+ sole patents, including about 10 specific to robot soles.

Performance figures are RobotSole targets and lab measurements from its own testing. Full test reports available on request.

Source: RobotSole (Shenzhen Zhilv Technology) technical documentation and robotsole.com. Full test reports available on request.

Put your robot on better footing.

Tell us about your robot. We reply within one business day and work out the right footwear with you, from specs to production, in the U.S.